• <bdo id="g6gk2"><blockquote id="g6gk2"></blockquote></bdo><input id="g6gk2"><blockquote id="g6gk2"></blockquote></input>
    <bdo id="g6gk2"></bdo>
  • <input id="g6gk2"><samp id="g6gk2"></samp></input>
    電話:15930299808 手機:13903124561
    新聞中心
    聯系方式
    保定金潤機械設備有限公司
    地址:保定市保滿路收費站東側路北
    聯系人:孟經理、吳經理
    手機:13903124561
    手機:15930299808
    網址:www.novemberthirteen.com
    生產加工:托輥設備、托輥機械制造
    首頁:公司動態 >> 帶式輸送機托輥是個簡單的小部件

    目前托輥制造存在的主要問題及分析 The main problems of roller manufacturing and analysis 帶式輸送機托輥是個簡單的小部件,正因為是小部件,歷來被忽視。托輥的結構設計較為簡單,如圖1 ,此結構是目前的規范結構,本文暫不探討設計結構問題,主要針對此結構分析研究加工工藝過程和托輥加工設備的加工方法,然后優化設計出托輥數控自動化生產線工藝優化方案,為托輥數控自動化生產線的設計提供工藝方案。 Belt conveyor roller is a simple widget, because be the widget, has always been neglected. Roller of the structure design is relatively simple, as shown in figure 1, this structure is the specification of the structure, temporarily not to discuss design problems, this paper focuses on the structure analysis of the machining process and processing method of roller processing equipment, and then optimize design of roller CNC automatic production line process optimization scheme, for the roller process scheme for the design of numerical control automatic production line. 圖1 托輥輥子 Figure 1 roller roller 1.1 托輥輥體 1.1 the roller roller body 如圖2,1-管子,2-軸承座,把軸承座放入管子兩端的止口內,然后在環式焊床上把軸承座和管子焊接在一起。 As shown in figure 2, 1 - pipe, 2 - bearing seat, put the bearing into the seam allowance at the ends of the pipe, and then the ring weld the bearing seat on the bed and tube welded together. 存在的工藝缺點是:1)軸承座和管子采用焊接工藝造成了軸承座熱變形,軸承座的內孔與管子的平行度受到了影響,也就是兩端的軸承座的同心度得不到保障,2)由于是手工安設軸承座,軸承座內孔與設備的頂頭公差較大(為了便于安設),軸承座的外徑與管子止口孔的公差也較大,實際制作的輥體,無法保證圖2中所標注的同心度。 Shortcomings of process are: 1) the bearing seat and pipe welding process caused by bearing thermal deformation, and the inner hole of the bearing with parallel pipe affected, namely the concentricity of the bearing at the ends of the protected, 2) because it is handmade make bearing seat, bearing inner hole and equipment of immediate larger tolerance (set) to facilitate, the outer diameter of the bearing and the tube through hole tolerance is bigger also, the actual production of the roller body, there is no guarantee that the concentricity of marked in figure 2. 圖2輥體 Figure 2 roller body 1.1.1 管子 1.1.1 pipe 目前托輥輥皮(也叫管子)加工的設備是上世紀80年代的產品,用于制造輥皮的鋼管,在徑向上公差較大并有橢圓度,在軸向上直度公差較大,加工出來的輥皮,基本無法保證徑向圓的跳動量。國家煤炭行業標準MT821-2006規定的徑向圓跳動量的最小值為0.7mm,采用現行的加工設備和鋼管加工的托輥輥皮,達標比率較低。 The idler roller skin (also called pipe) processing equipment is the product of the 1980 s, used in the manufacture of steel pipe roller skin, on the radial tolerance is larger and the ovality, tolerance is larger in the shaft straightened, roll leather processing, basic is no guarantee that the radial beat quantity of the circle. MT821-2006 national coal industry standard amount of radial round to beat the minimum value of 0.7 mm, with the current machining equipment and steel pipe roller roller skin, standard ratio is low. 具體問題有: Specific questions are: 1)管子鏜口時,管子2端止口間的距離,即圖3中尺寸937,誤差較大并數值分散,誤差值一般在3mm范圍。此誤差給托輥軸的加工帶來了不便。若托輥軸完全按圖紙要求加工,就會有30%以上的托輥輥體與軸,由于軸上軸用擋圈槽的距離相對小,而無法裝配。目前實際加工中,為了解決相互尺寸不配套的問題,大多數的廠家只好放大托輥軸上軸用擋圈槽的距離,一般放大值在3-5mm。放大后雖然解決了無法裝配的問題,但又帶來了30%以上的托輥軸向穿動量超標,影響了現場使用。之所以產生此類問題,是由于加工設備落后,采用無觸點限位開關設定進給行程。 1) the pipe boring, pipes, the distance between two side seam allowance, namely the size in figure 3, 937, and the numerical dispersion error, error value generally in the range of 3 mm. This error brought inconvenience to the supporting roller processing. If the roller completely according to the drawing requirements processing, there will be more than 30% of the idler roller and shaft, due to the shaft axis with the distance of the ring groove is relatively small, and can't assembly. In the actual processing, in order to solve the problem of size don't match each other, most of the manufacturers have to enlarge the distance with the retaining ring groove on the roller shaft as, general zoom value in 3 to 5 mm. Enlarged although have solved the problem of unable to assembly, but also brought momentum to exceed bid more than 30% of the roller to wear, impact on the field use. Is such a problem, is due to the processing equipment, using non-contact limit switch set feeding schedule. 2)管子鏜孔設備夾持管子的夾具沒有糾偏對準功能,采用V型鐵或圓錐內表面的方法來夾持或頂持輥皮并設定軸向中心,然后兩端鏜口或倒角,加工出安放軸承座的止口或引導口,加工出的管子外皮相對于管子2端止口的軸線,徑向跳動量較大。原因有三點,其一是管子端口與管子軸線的垂直度誤差,其二是管子端口的橢圓度及直徑誤差,其三是設備的設計缺陷及精度。 2) pipe boring equipment clamping pipe clamp without correction function, adopt the method of v-shaped iron or conical surface to clamping or a roller skin and set the axial center, and then on both ends of the boring or chamfering, work out put the seam allowance or guide mouth of bearing seat, work out the tube skin relative to the pipe axis of the 2 end, radial runout is high. The reason has three, one is the pipe port with the pipe axis perpendicularity error, error of the second stage is the ovality and the diameter of the pipe port, the third is the design defects and the accuracy of the equipment.

    [來源:原創] [作者:aoutmy] [日期:17-04-01] [熱度:]
    版權保定金潤機械設備有限公司 電話:15930299808 手機:13903124561 新聞技術 網址:www.novemberthirteen.com
    地址:保定保滿路收費站東側路北 生產加工:托輥設備、托輥加工設備、托輥生產設備、托輥機械設備制造廠家,托輥設備價格公道!
    友鏈推薦:不銹鋼鑄件
    保定網站建設及優化保定遨游網絡公司
    影音先锋2020色资源网,影音先锋男人色资源网,影音先锋5566中文源资源,欧美人牲交免费观看,欧美在线看片高清无码,欧美亚洲日本韩国一级毛片_第1页